EZ-Bridge®
How do I access the EZ Bridge’s Web Interface?
You can access the EZ Bridge’s web interface by going to its IP address. By default, the EZ Bridges are set as DHCP clients, meaning they will be assigned an IP address automatically by your router or DHCP server. If for any reason the EZ Bridges do ...
How can I set up a repeater on an EZ-Bridge LT or LT+ running WISPOS software?
Applicable Models: EZ-Bridge LT and LT+ Setting up a repeater is relatively easy. It is used when you have three or more units and the third unit cannot communicate well with the main Access Point, so you set up the intermediate unit as a repeater. ...
How can I determine if my EZ-Bridge antenna system is working?
Applicable Models: All EZ-Bridge models There are different ways on checking if your EZ Bridge is working. After following the instruction manual on setting up the EZ Bridge, you may check if the EZ Bridge is working by: Checking the LED lights at ...
How do I use the EZ-Bridge as a Wi-Fi access point?
Applicable Models: All EZ-Bridge models If you need wireless access at the installation point: Start by making changes on the remote unit (Unit B). Switch the mode from “Station (WDS)” to “Station”. Do this by going to: Network >> Wi-Fi >> Edit >> ...
What is the best method/procedure to follow for first time installs of the EZ-Bridge?
Applicable Models: All EZBR models For initial setup instructions, please refer to the white papers in the link below. The white paper is specifically for the EZBR-LT2, but the procedure is the same for our other models. ...
What changes are required to the EZ-Bridge setup to get the system up and running?
Applicable Models: All EZ-Bridge models Please be aware that typically, no changes are required to get the units running and create a wireless bridge. Our EZ-Bridges are designed as plug-and-play units. All that is needed is to power the units up, ...
My EZ-Bridge was working but now it keeps dropping connection or performance has degraded. What could be the problem?
Applicable Models: All EZ-Bridge models If your system was working but now seems to be sluggish or it is dropping connection, the most likely culprit is that a new wireless device was added to your environment and there is wireless interference ...
What changes should I make to the EZ-Bridge when changing to a Multipoint system?
Applicable Models: EZBR-DUAL-AC EZBR-0214+ The EZ-Bridge ships from the factory configured as a Point-to-Point system. Sometimes people need to create a multipoint system where there is one Access Point and multiple client antennas. One application ...
Can the EZ-Bridge® be used with VLANs?
Products: EZBR-0214+ EZBR-DUAL-AC EZBR-5AC EZBR-DUAL-AC+ The EZ-Bridge® creates a layer 2 bridge between two points. The EZ-Bridge® will pass all untagged VLAN packets. The EZ-Bridge is not compatible with VLAN Trunking or VLAN Tagged Frames. The new ...
How do I set up the EZ-Bridge-LT+?
Applicable Models: EZ-Bridge ®- LT+ Series Initial Set-Up Procedure and Checklist: Thank you for choosing the EZ-Bridge® Wireless Antenna System. Each Antenna system is factory tested and pre-configured so that most applications are true “Plug and ...
Can I Use the Second Ethernet Port to Link Two Separate Access Points Together?
Applicable Models: All EZBR models The two ethernet ports under the antenna can accept 12-24V PoE. They are used to power on the antenna. They will not provide any PoE out. The two ports also act like a switch. A device connected to the spare ...
How to change the transmit channel on an EZ-Bridge Ultra?
Applicable models: EZ-Bridge Ultra To Change transmitter frequency, open the Unit A Access Point Web Control Panel. Navigate to Wireless tab and change frequency to a fixed frequency rather than “Auto”. The Unit B Client will follow automatically ...
How do I turn on ping watchdog to automatically reboot the EZ-Bridge Ultra antennas?
Applicable Models: EZ-Bridge Ultra Navigate to the Services Page. Enable Ping Watchdog and enter the IP address of the other antenna into the “IP Address to ping” field. Do this for both antennas. The result will be if the antennas lose connection ...
How many IP Cameras can I use with my EZ-Bridge LT2+ or LT5+ wireless link?
Applicable Models: EZ-Bridge-LT+ EZ-Bridge-LT2+ EZ-Bridge-LT5+ The EZ-Bridge LT+ can support up to 100Mbps bandwidth. Normally people will see around 80Mbps due to RF interference or electrical noise or multi-path issues which cause packet retries ...
How can I secure SSH and Telnet on the EZ-Bridge?
Applicable Models: All EZ-Bridge models If you want to tighten the security of accessing the EZ-Bridge unit through a terminal program like SSH or Telnet, we recommend the following: Set the listening port to a custom port. Any port other than 22 or ...
How do I connect an EZGO+ to my EZ-Bridge LT+?
Applicable models: EZBR-LT+ EZBR-LT2+ EZBR-LT5+ EZGO+ EZGO-2+ EZGO-5+ There are 2 main requirements so you can have another receiver in your EZ-Bridge LT+ setup. Make sure the 2nd receiving antenna would be within a 35-degree beamwidth of the ...
How do I reconfigure my EZBR-0214+ for side A and B firmware?
Applicable models: EZBR-0214+ If you accidentally erased the firmware on your bridge you can visit Click here in order to get the side A and B firmware. When you download the firmware to a computer you will need to open the antenna A GUI. You can get ...
EZ-Bridge LT+ TyconOS Wiki
The information below is for EZ-Bridge® This information is used for the following models: EZBR-0214+; EZBR-DUAL-AC Status Overview The overview page contains link status information and other pertinent info regarding active WIFI and LAN interfaces. ...
Status page explanation for the EZ-Bridge® (EZBR-0214+ and EZBR-DUAL-AC)
Applicable models: EZBR-0214+ EZBR-DUAL-AC EZGO-0214+ EZGO-DUAL-AC The EZBR-0214+ and the EZBR-DUAL-AC use the same firmware and have the same status page. Below you will find descriptions of each bar that will make it easier to understand. This is ...
Will my speed slow down at extended distances?
Applicable models: All EZBR and EZGO models At the recommended max distance with a clear line-of-sight and minimal external interference, the EZ-Bridge® will perform as advertised. However, if there are obstacles in the path or excessive external ...
Is it better to use a 2.4GHz or 5GHz EZ-Bridge?
Applicable models: EZBR-0214+ EZBR-5AC EZBR-DUAL-AC EZGO-0214+ EZGO-5AC EZGO-DUAL-AC 5GHz Bridges absolutely need to have a clear line of site. With 2.4GHz Bridges, a clear line of site is still the absolute best, but it is a little more forgiving ...
Can I power a second device off my EZ-Bridge-LT+?
Applicable models: EZBR-LT+ The RJ45 connectors on the LT+ don’t have PoE output capability, but you can use a 5.5 x 2.1mm DC Plug Jumper to power up the second EZ-Bridge. Maximum 10W output @ 15-24V DC. Note: The EZ-Bridge requires much less than ...
Can I power your EZ-Bridge products from a standard PoE Switch?
Applicable models: EZBR-DUAL-AC EZ-Bridge LT+ EZ-Bridge HD EZ-Bridge ULTRA It depends on the model: EZBR-Dual-AC can be powered from a standard PoE Switch which is 48V PoE. The EZ-Bridge LT+, HD, and ULTRA require 15V to 24V Passive PoE The EZ-Bridge ...
How can I connect two separate networks across an EZ-Bridge Ultra?
Applicable models: EZ-Bridge Ultra It is possible to have two separate networks connected through the EZ-Bridge Ultra You can have an EZ-Bridge Ultra connecting a network at the Local side with a network at the Remote side, using two routers, one ...
Do I need to be an engineer or technical person to install and operate the EZ-Bridge?
Applicable Models: All EZBR models The EZ-Bridge® is plug and play with no setup required. If you can install a wireless router or computer peripheral, you should have no problem with the EZ-Bridge.
How critical is line of sight when using the EZ-bridge?
Applicable Models: All EZBR models With Wireless Bridges, a clear line of sight is always recommended. Any obstructions like trees, poles, fences, and buildings can block or reduce the power of a wireless signal. 5GHz is more sensitive to line of ...
How do I access the EZ-Bridge® to change settings?
Applicable Models: All EZ-Bridge Models The EZ-Bridge® comes from the factory programmed to be plug and play. If the units are installed and powered up, they will automatically bridge the networks. If you want to change settings for any reason, you ...
Can I have a router on both sides of the EZ-Bridge® link?
Applicable models: EZBR-0214+ EZBR-5AC EZBR-DUAL-AC EZGO-0214+ EZGO-5AC EZGO-DUAL-AC Yes, on the internet side of the link, the EZ-Bridge® would be connected to one of the LAN ports on the main router. On the remote side of the link the EZ-Bridge® ...
Why can’t I open the EZ-Bridge® unit’s web page with my browser?
Applicable Models: All EZ-Bridge Models To open the EZ-Bridge® web page with your browser you need to type in the IP address of the EZ-Bridge® into the address bar of a web browser (like Firefox, Chrome, etc.). Your computer must be on the same ...
What QOS settings should I use on the WISPOS firmware?
Applicable Models: EZBR-0214+ EZBR-DUAL-AC For the bandwidth to be used by anyone when not used by higher priorities you should check the “Bandwidth Borrowed” checkbox. Then there is the “Max Throughput” field which, as the name suggests, sets the ...
How do I know if my bridges are communicating?
Applicable Models: All EZ-Bridge models Caution: When connecting and disconnecting Ethernet cables between the POE inserter and the Bridge, do so ONLY when the POE inserter is unplugged from the AC socket. Connecting/disconnecting CAT5/6 cables while ...