mobilesolarpro
 
Tightening screws on MPPT controllers
The screws on our MPPT controllers need to be hand driven. An elextric screw driver or impact driver can easily over tighten the screws resulting in permenant damage. The maximum torque spec is 15 in-lb-max. This goes for all of our MPPT charge ...
 
Why does the load output of my solar controller keep shutting down?
There are a couple reasons why the load output on the controller will turn off. 1. If the batteries get too low (11V for 12V battery, 22V for 24V battery, or 44V for 48V Battery) the load output will turn off. This is to save the batteries from ...
 
Which systems come with a pole?
All RemotePro systems with a 720W solar array or larger will come with a top of pole mount and a 6 inch round, 72 inch long pole that needs to be anchored to a concrete footing.
 
Can I add more devices to my RemotePro system without increasing the panels and batteries?
You may need to add additional panels or batteries in order to allow new equipment to be introduced. You can calculate it by going to: “https://tyconsystems.wpenginepowered.com/calculators” Input your new total power draw, peak sunlight hours and any ...
 
How high should I install my solar panel and enclosure?
That will depend on your application. Mounting your enclosure and solar panels high above the ground will discourage vandalism. It’s important to mount the solar panels above any obstacles that may cause shade. Maximum sunlight exposure is most ...
 
How can I add a grid or generator powered battery charger to my RemotePro system with MPPT solar controller?
The following wiring diagram shows how to add an AC powered battery charger to the RemotePro system to provide supplemental charging of the batteries.
 
Can I lengthen the cable between the solar controller and the solar panels?
Most of the Tycon RemotePro® systems come with a 20′ 12AWG cable. Sometimes a customer may want to mount the solar panels at a different location than the solar controller/batteries. This can be done as long as you understand that if you extend the ...
 
Where can I find a rackmount for my RPSTL/ENC-STL enclosure? Are there 2U or 4U rackmounts available for Tycon Large Enclosures?
We don’t offer rack mounts, other than the built-in 1U included in the STL enclosure, but they are available in the open market.
 
What information do you need to help me size a system?
Applicable Models: RemotePro Systems UPSPro Systems MobileSolarPro Systems Our system design team is happy to help you find the right system for your needs. In order to do so, we will need to know the maximum power draw in Watts for each piece of ...
 
I have my system hooked up but I’m not getting the correct voltage out of the controller, what’s wrong with it?
Most often this might be caused by loose or incorrect connections, or the product is designed for a different application. First check the installation manual to be sure all connections are correct, and that the device is designed to supply the ...
 
Are the solar systems shipped complete with everything I need?
Systems are shipped with everything that is needed except the mounting pole or tower and CAT5 cables (if needed to interconnect equipment). Note: For 720W and 1300W solar systems, they come with the mounting pole included.
 
What hardware comes with my TPSM-80×4-UNI solar mount?
Applicable Models: TPSM-80x4-UNI RemotePro Systems MobilSolarPro Systems UPSPro Systems TPS-12-85W TPS-24-360W The TPSM-80x4-UNI comes with the necessary bolts, framework, hose clamps, and fasteners for panel attachment, and contains a guide to walk ...
 
How long will my battery backup power my equipment? How much autonomy should I expect?
Applicable Models: RemotePro Systems UPSPro Systems MobileSolarPro Systems TPBAT12-9 TPBAT12-50 TPBAT12-180 There is a free calculator to calculate battery backup time at: https://tyconsystems.com/tycon-support/tycon-calculators/ To figure out how ...
 
How do I calculate how many solar panels/what solar panel wattage is needed to support my equipment?
Applicable Models: RemotePro systems UPSPro systems MobileSolarPro systems We have a free system requirements calculator located at: https://tyconsystems.com/tycon-support/tycon-calculators/ You can use the online calculator or follow the guide below ...
 
RemotePro® and UPSPro® Battery Care
RemotePro® and UPSPro® systems are designed to maintain proper battery charge within a defined range. Our systems have protections for over-discharge of batteries but batteries also self-discharge over time, so if they are left without any charge or ...
 
RemotePro® and UPSPro® Troubleshooting
Minimum Equipment Needed: - A voltmeter that can show DC voltage. - Wire Ferrules sized 12-18AWG is suggested depending on the system. Measure the battery voltage at the solar charge controller ports and then on the battery terminals to verify the ...
 
How long will my battery backup power my equipment?
To figure out how long a battery backup system will keep your equipment powered there is a fairly simple calculation you can do: ((Battery Capacity (Ah) x Battery Voltage (12V)) x Percent Discharge (50%)) / Your Equipment Load (W) So let’s say your ...
 
Do I need to ground my RemotePro or UPSPro system?
Applicable Models: RemotePro systems UPSPro systems Over the course of Tycon's history, we haven't had many issues regarding ungrounded systems. As such, grounding our solar systems is not required as long as the mounting pole is grounded. If ...
 
How do I connect my TP-SW8GBT/AT/PSV-U or TP-SW16GBT/AT/PSV-U Switch to the Tycon MPPT Solar Controller?
Applicable to the following products: TP-SW8GBT/AT/PSV-U TP-SW16GBT/AT/PSV-U TS-SC24-40N-MPPT TS-SC24-60N-MPPT TS-SC48-60P-MPPT TP-SC24-30N-MPPT TP-SC24-40N-MPPT Tycon manageable PoE Switches such as the TP-SW8GBT/AT/PSV-U and TP-SW16GBT/AT/PSV-U can ...
 
Install and concrete footer information for TPSM-350×2-TP
Applicable to TPSM-350x2-TP Installation Steps: 1. Use the 4 J bolts provided cast into a concrete foundation suitable for the location and the expected loads on the structure. Minimum recommended is 1200mm (48”) Deep and 600mm (24”) square, or about ...